Genelec Community Forum has been archived

Thank you for all the years of Community discussions and activity!

The time has come for us to retire the community forums, but we will keep everything available for reading. There is a lot of valuable content written over the years, and you'll be able to access all of that. However, no new posts can be written, or old posts modified.

If you have questions, we recommend you use the Support function on the bottom right corner to contact our Customer Support directly.

Alternatively, if you wish to engage in a community discussion with other people, there are many active forums available. There is also an active, fan managed GENELEC COMMUNITY in Facebook, and many Genelec employees are active in the discussions there.

We are sorry for any possible inconvenience this may cause you, but we hope to hear from you through the other channels mentioned above.

Genelec Support

Keskusteluryhmät

Reference level at custom value

soundmixdude, muokattu 1 Vuosi sitten.

Reference level at custom value

Youngling Viestejä: 6 Liittymispäivä: 25.12.2018 Viimeisimmät viestit

I like to change the system level of my 8351a's. The reference level to operate on my reference noise from the DAW. I need 10 more dB from the speaker to be on the correct level. I noticed dip switches that can change that. E.g. from -30 dB (all dip switches on) to -20 dB. That gives exactly the 10 dB that I need. Changing those dip switches doesn't change the level. I have a GLM. In the software the dip switch has been noticed that it is changed. But there is no change in level. How do change this system level?

jani-oksanen, muokattu 1 Vuosi sitten.

RE: Reference level at custom value

Jedi Master Viestejä: 449 Liittymispäivä: 30.3.2017 Viimeisimmät viestit

Hi there,

When using GLM network, it override the DIP-switch settings. Using Stored-DIP switch also override other DIP-switch settings.To control volume with GLM, please see picture below which shows where you can adjust:

 

 

Please contact us at support@genelec.com, if you require further instructions and we are glad to assist more.

Best Regards,
Jani Oksanen
​​​​​​​Customer Support Team

soundmixdude, muokattu 1 Vuosi sitten.

RE: Reference level at custom value

Youngling Viestejä: 6 Liittymispäivä: 25.12.2018 Viimeisimmät viestit

Thank you Jani for replying my message. Your attached picture gives a question mark and therefore it cannot be displayed.

soundmixdude, muokattu 1 Vuosi sitten.

RE: Reference level at custom value

Youngling Viestejä: 6 Liittymispäivä: 25.12.2018 Viimeisimmät viestit

In my case I would like to have the 79 dB SPL read out at -20 dB. It seems that my sound device is low on the output. I use a Focusrite Scarlet 18i20. Something tells me that the 79 dB SPL was correct a year ago. Since I updated my equipement to a 7.1 setup this happened. I am not sure. Thats why I am checking to see if there are settings on the GLM to adjust the analogue in level.

jani-oksanen, muokattu 1 Vuosi sitten.

RE: Reference level at custom value

Jedi Master Viestejä: 449 Liittymispäivä: 30.3.2017 Viimeisimmät viestit

Hello,

​​​​​​​I apology, please find attached below. If this is not what you are looking for, I would recommend to contact us at support@genelec.com ​​​​​​​and we are glad to assist further.


​​​​​​​Best Regards,
Jani Oksanen
​​​​​​​Customer Support Team