Genelec Community Forum has been archived

Thank you for all the years of Community discussions and activity!

The time has come for us to retire the community forums, but we will keep everything available for reading. There is a lot of valuable content written over the years, and you'll be able to access all of that. However, no new posts can be written, or old posts modified.

If you have questions, we recommend you use the Support function on the bottom right corner to contact our Customer Support directly.

Alternatively, if you wish to engage in a community discussion with other people, there are many active forums available. There is also an active, fan managed GENELEC COMMUNITY in Facebook, and many Genelec employees are active in the discussions there.

We are sorry for any possible inconvenience this may cause you, but we hope to hear from you through the other channels mentioned above.

Genelec Support

Keskusteluryhmät

Subwoofer configuration

mikko-pm, muokattu 12 Vuodet sitten.

Subwoofer configuration

Youngling Viestejä: 2 Liittymispäivä: 2.7.2009 Viimeisimmät viestit
Hi,

I added a 7050b subwoofer to my 8030 stereo monitoring system. I don't have a measuring equipment available at the moment so I tried to make the adjustments by ear following the manuals instructions.

My control room is small (3.3 x 4.6 x 2.6m) but it's filled with bass traps and broadband absorbers and I've managed to make the room's response quite decent for professional working.

The problem is that I have very limited space for the subwoofer's placement and I cannot experiment without making some rearrangements in the room. Anyway, I placed it between the speakers about 50-60cm from the front wall, little bit off from the center and it sounded ok by itself. But when I added the 8030s (85Hz lo pass for sub, 85 hipass for speakers) no matter how I set the phase there was always a significant dip around the crossover frequency, or at least I just couldn't get satisfying settings. Also that frequency range is actually pretty good and flat without the subwoofer so it must be somekind of phase issue.

But, then I tried to remove the 85Hz hipass from the speakers and it started to sound much flatter and better.

Of course I have to do more listening tests and experimenting, but is there any pitfalls using the system like this if it turns out that it just sounds (or measures) the best that way?

- Mikko
christophe-anet, muokattu 12 Vuodet sitten.

Re: Subwoofer configuration

Jedi Knight Viestejä: 188 Liittymispäivä: 23.3.2009 Viimeisimmät viestit
Dear Mikko,

Thanks for your post. Nice setup you have indeed. First, some comments on the sub placement in the room.

> Try to move the sub right against the wall and do not leave the 50-60 cm from the wall behind the sub. That distance is a bit large and it would be best to minimize it. The off-center position from the symmetry axis in the room is very good. Keep that.

> For the connection scheme, more details are featured in our FAQ under: http://www.genelec.com/faq/multichannel ... 50b-8020a/
It is recommended to set the "BASS ROLL-OFF" switch on the 8030A's to "ON" (switch 2) to make sure the LP and HP curves complement each other perfectly.

> Now, for the phase adjustment, you could follow the simple steps outlined in our Quick Setup Guide:
http://www.genelec.com/documents/qsg/QS7050b.pdf
You should be able to find quite quickly and without measuring equipment a setting that gives you a flat response around the crossover region.

Let us know your findings!
Best regards,
mikko-pm, muokattu 12 Vuodet sitten.

Re: Subwoofer configuration

Youngling Viestejä: 2 Liittymispäivä: 2.7.2009 Viimeisimmät viestit
Thank you very much for your reply Christophe.

I'll come back from a vacation after two weeks and experiment more then. I'll let you know how it turns out.

- Mikko