Genelec Community Forum has been archived

Thank you for all the years of Community discussions and activity!

The time has come for us to retire the community forums, but we will keep everything available for reading. There is a lot of valuable content written over the years, and you'll be able to access all of that. However, no new posts can be written, or old posts modified.

If you have questions, we recommend you use the Support function on the bottom right corner to contact our Customer Support directly.

Alternatively, if you wish to engage in a community discussion with other people, there are many active forums available. There is also an active, fan managed GENELEC COMMUNITY in Facebook, and many Genelec employees are active in the discussions there.

We are sorry for any possible inconvenience this may cause you, but we hope to hear from you through the other channels mentioned above.

Genelec Support

Keskusteluryhmät

Height adjustable stand for 8341

tommi14, muokattu 5 Vuodet sitten.

Height adjustable stand for 8341

Youngling Viestejä: 2 Liittymispäivä: 25.10.2010 Viimeisimmät viestit

I am searching a height adjustable stand for 8341 (an possible for some smaller Genelecs as well). The stand would be for occasional use at a home environment. The stand 8000-409 would be adequate, but I need the stand to go lower.

Would it be possible to take saw and shorten the tubes of the 8000-409? :) Is the locking mechanism on the top of the lower tube removeable?

If the shortening is not possible, what would be a better choice for my need? The stand should accept Genelec stand adapters, and the height of the stand should be adjustable at least between 70-90 cm (so that I could adjust the height of the acoustical axis of 8341 between 90-110 cm).

jani-oksanen, muokattu 5 Vuodet sitten.

RE: Height adjustable stand for 8341 (Vastaus)

Jedi Master Viestejä: 449 Liittymispäivä: 30.3.2017 Viimeisimmät viestit

Hi Tommi,

Shortening the 8000-409 is not an easy to do, as the locking mechanism on the top is really tight. It is probably glued. If you wish, you can confirm this from K&M who is the manufacturer for the stands, and ask if they have an alternative solution to offer you.

https://www.k-m.de/en/supportunddownloads/support.html

Br,
Jani Oksanen
Factory Service Team

tommi14, muokattu 5 Vuodet sitten.

RE: Height adjustable stand for 8341

Youngling Viestejä: 2 Liittymispäivä: 25.10.2010 Viimeisimmät viestit

Moi Jani,

Ok, thanks! I looked through the K&M catalogue and there would be several suitable stands if only they went lower. Maybe I email them and ask if there are any other solutions.

Tommi

klauswerner, muokattu 5 Vuodet sitten.

RE: Height adjustable stand for 8341

Youngling Viestejä: 7 Liittymispäivä: 13.7.2017 Viimeisimmät viestit


Hi Tommy,

if you use the monitor stand 8000-400 in combination with the 8341A the height 

of the acoustical axis is at 1048mm on the lowest position of the stand.

You can adjust the height in 50mm steps.

 

Klaus

 

jani-oksanen, muokattu 5 Vuodet sitten.

RE: Height adjustable stand for 8341

Jedi Master Viestejä: 449 Liittymispäivä: 30.3.2017 Viimeisimmät viestit
Klaus Werner:


Hi Tommy,

if you use the monitor stand 8000-400 in combination with the 8341A the height 

of the acoustical axis is at 1048mm on the lowest position of the stand.

You can adjust the height in 50mm steps.

 

Klaus

 



Thank you Klaus, that is correct. Please see more information from two link below:

 

https://www.genelec.com/sites/default/files/media/Support%20and%20Technology/Technical%20LIbrary/Accessories%20Line%20Drawings/8000-400_km_267858030a.pdf

 

https://www.genelec.com/sites/default/files/media/Support%20and%20Technology/Technical%20LIbrary/Accessories%20Manuals/26785_design_monitorstativ.pdf

 

Best Regards,
Jani Oksanen
Factory Service Team